Skycontroller update

Questions and answers about Bebop, Bebop 2 and the Parrot Skycontroller.
Pliskin59
Newcomer
Posts: 2
Joined: 10 Jan 2019, 14:21
Drone Type: Bebop
Has thanked: 0
Been thanked: 0

Re: Skycontroller update

Post by Pliskin59 » 10 Jan 2019, 14:36

I couldn't get the controller to connect to the bebop , so I downloaded the update on the 1st Jan 2019 , it worked but stopped working the next day. Will I have to download it to USB again & install it again?

Pliskin59
Newcomer
Posts: 2
Joined: 10 Jan 2019, 14:21
Drone Type: Bebop
Has thanked: 0
Been thanked: 0

Re: Skycontroller update

Post by Pliskin59 » 11 Jan 2019, 02:18

i downloaded the update from this thread , but not working. I can connect to the Bebop on its own from the app & control using my iPad mini , I can connect to the Skycontroller with the app & iPad mini , but the controller can find the Bebop Wifi ,but the iPad mini can ?

Ledroneux
Newcomer
Posts: 1
Joined: 12 Jan 2019, 02:25
Drone Type: Bebop
Has thanked: 0
Been thanked: 0

Re: Skycontroller update

Post by Ledroneux » 12 Jan 2019, 03:14

Help me !!!! I try no harm to update my skycontroller 1 for 1 week but every time I get message that shows me!
Searching for update file ... word found ..
Help me my USB key is in fat32 I tried the update to parrot and had online I made rest of my skycontroller I know what to do!
Aider moi !!!! J'essaie sans bien que mal de faire la mise à jour de mon skycontroller 1 depuis 1 semaine mais a chaque fois j'ai se message qui m'affiche !
Searching for update file ...mot found ..
Aider moi ma clé USB est en fat32 j'ai essayé les mise à jour à parrot et eu ligne j'ai fait des rest de mon skycontroller je sais plus quoi faire !!

Gamedex
Newcomer
Posts: 1
Joined: 08 Feb 2019, 08:51
Drone Type: Bebop
Has thanked: 0
Been thanked: 0

Re: Skycontroller update

Post by Gamedex » 08 Feb 2019, 08:59

rickiwada wrote:
14 Nov 2018, 16:40
Hello everyone, my name is Riccardo and i've buy my frst drone, a Bebop version 1 with the skycontroller.
When I turned on the drone via app immediately asked me to do the update. All right.
Then, i've update skycontroller.
At the end of the installation I received the message that you see attached.
What can I do? The skycontroller seems to be dead, it does not allow it to perform any operation.
I tried to turn on the bebop too, hopefully enough, but nothing happens.
From the app the skycontroller is disconnected, I can connect it to its wifi network but in the app is disconnected.
Someone would know how to solve?
Thank you
Hello Ricardo, I hope you haven't given up on your bebop and skycontroller yet. I just had the very same issue like yours. I was able to fix mine. Follow waterlanding's advice. Download that firmware using the link he provided. Its a 161mb file. Anything less and it will not work obviously. I am saying this because my first , second and third downloads was less than 161mb. It may be my connection, but in case it happens to you too, remember that its a 161mb file. Just repeat the download if needed, and rename the file to nap_update.plf before you transfer to usb.

To waterlanding, thank you for providing the link.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests