Login to disable ads!

v1 parts on v2

Problems of AR Drone 2.0, Freeflight 2, Flight Recorder GPS, Qgroundcontrol... etc.
Post Reply
nabisco
Thinking of bearings
Posts: 155
Joined: 25 Dec 2012, 02:36
Drone Type: AR.Drone
Has thanked: 0
Been thanked: 0

v1 parts on v2

Post by nabisco » 11 Apr 2014, 20:25

will the motor on a v1 work on a v2, how about the bearings and the little sprocket that turns the big sprocket? how do i get the little sprocket off?

User avatar
DBS
I've been hit!!
Posts: 2764
Joined: 15 May 2012, 16:27
Drone Type: DISCO
Location: Treasure Coast, Florida
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by DBS » 11 Apr 2014, 20:59

Sprocket on AR1 is brass with a D shaft... comes off hard and won't fit round shaft on AR2 motor...

Motor assemblies are compatible... bearings are compatible
WORLD RECORD Phantom 4 flight CLICK HERE
WORLD RECORD Matrice 600 flight CLICK HERE

nabisco
Thinking of bearings
Posts: 155
Joined: 25 Dec 2012, 02:36
Drone Type: AR.Drone
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by nabisco » 11 Apr 2014, 21:07

do u have a link to the part i need or does it not matter matter i plan to upgrade to the bushings garrock has soon

User avatar
DBS
I've been hit!!
Posts: 2764
Joined: 15 May 2012, 16:27
Drone Type: DISCO
Location: Treasure Coast, Florida
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by DBS » 11 Apr 2014, 23:16

Be more specific... which part do you need a link too?
WORLD RECORD Phantom 4 flight CLICK HERE
WORLD RECORD Matrice 600 flight CLICK HERE

nabisco
Thinking of bearings
Posts: 155
Joined: 25 Dec 2012, 02:36
Drone Type: AR.Drone
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by nabisco » 12 Apr 2014, 00:50

the shaft that the prop is on wobbles, would that be fixed by putting bushings? ty

User avatar
DBS
I've been hit!!
Posts: 2764
Joined: 15 May 2012, 16:27
Drone Type: DISCO
Location: Treasure Coast, Florida
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by DBS » 12 Apr 2014, 01:26

Oh ok.... yeah worn bushings are a bummer for sure... If you're gonna swap them out then go ahead and upgrade to bearings...


A few different prices available from boca bearing... even the cheap ones are a step up from bushings
http://www.bocabearings.com/bearing-inv ... adricopter

Or ebay... These ones are really good
http://ebay.com/itm/111169913342?
WORLD RECORD Phantom 4 flight CLICK HERE
WORLD RECORD Matrice 600 flight CLICK HERE

nabisco
Thinking of bearings
Posts: 155
Joined: 25 Dec 2012, 02:36
Drone Type: AR.Drone
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by nabisco » 12 Apr 2014, 22:52

i switched 2 v1 motors over and it would not work i thought they were the same? i even reset the drone? i broke the pinion gear.... i found some on ebay but y wont the motors work?

Witmore
Just flips over
Posts: 55
Joined: 29 Apr 2013, 16:14
Drone Type: AR.Drone 2
Location: Columbus, Ohio
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by Witmore » 14 Apr 2014, 02:40

I dunno, my drone has a V1 motor on it currently, and the only thing that didnt work is that when it does the 4 motor twitch at the beginning, it whines but doesnt twitch as much as the other V2 motors do, but it flew and hovered well when it did. could be you got a bad v1 motor,

User avatar
DBS
I've been hit!!
Posts: 2764
Joined: 15 May 2012, 16:27
Drone Type: DISCO
Location: Treasure Coast, Florida
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by DBS » 14 Apr 2014, 03:22

I had a 2.0 for a short time here for antenna work and it had ALL V1 motors on it... The guy said he liked the sound and durability of the brass gears so he switched all of them. I flew it here and seemed normal but sounded a lot louder than the 2.0
WORLD RECORD Phantom 4 flight CLICK HERE
WORLD RECORD Matrice 600 flight CLICK HERE

nabisco
Thinking of bearings
Posts: 155
Joined: 25 Dec 2012, 02:36
Drone Type: AR.Drone
Has thanked: 0
Been thanked: 0

Re: v1 parts on v2

Post by nabisco » 14 Apr 2014, 03:51

I tried 2 motors!

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest